Digilent JTAG Series Accessories

starting 76,16
including VAT plus shipping
min Quantity
1 piece
Unit price
base price
Variants
technical Question?
recommend by email
close
Please fill in all fields.
Question Type
Your E-mail Adress
My Question:
Please validate that you are not a robot.
Description
Files/Downloads

Digilent JTAG Series Accessories

ModelDescription
JTAG-SMT2410-251
  • Small, complete, all-in-one JTAG surface-mount programming/debugging solution for Xilinx FPGAs.
  • Compatible with Xilinx tools.
  • Compatible with IEEE 1149.7-2009 Class T0 – Class T4 (includes 2-Wire JTAG).
  • GPIO pin allows debugging software to reset the processor core of Xilinx's Zynq platform.
  • Single 3.3-V supply.
  • Separate VREF drives JTAG signal voltages; VREF can be any voltage between 1.8 V and 5 V.
  • High-Speed USB2 port that can drive JTAG/SPI bus at up to 30 Mbit/s (frequency settable by user).
  • SPI programming solution (modes 0 and 2 up to 30 Mbit/s, modes 1 and 3 up to 2 Mbit/s).
  • Uses micro-AB USB2 connector.
  • Small form-factor surface-mount module can be directly loaded on target boards.
  • A similar circuit is available as a stand-alone programming cable; see JTAG-HS2.
  • Analog Devices ADP123AUJZ linear regulator.
  • Fully supported by Digilent's Adept software and Adept SDK.
  • Product compliance: HTC: 8471801000, ECCN: EAR99.
  • Included: One JTAG-SMT2 programming module.
JTAG-SMT3-NC410-357
  • Small, complete, all-in-one JTAG surface-mount programming/debugging solution for Xilinx FPGAs with UART side channel.
  • Compatible with Xilinx Tools.
  • High-Speed USB 2.0 port that can drive JTAG bus up to 30 Mbit/s (frequency settable by user).
  • Open drain buffer on PS_SRST_B pin allows debugging software to reset the processor core of Xilinx's Zynq platform.
  • Dual channel USB controller provides simultaneous access to both JTAG and UART interfaces.
  • Separate VREF for JTAG and UART signals allows each interface to operate at different voltages (1.8 V to 5.5 V).
  • Small form-factor surface-mount module can be directly loaded on target boards.
  • USB D+ and D-signals routed to pads, allowing USB connector to be placed anywhere on the host PCB.
  • VBUS_DETECT pin allows for reduced current consumption when the module isn’t connected to a PC.
  • Product compliance: HTC: 8473301180, ECCN: EAR99.
  • Included: JTAG-SMT3-NC programming module.
JTAG-SMT4410-408
  • Small, complete, all-in-one JTAG programming/debugging solution for Xilinx FPGAs with UART side channel.
  • Compatible with Xilinx Tools (Vivado/Vitis 2020.1 or newer required).
  • Three independent UART channels each supporting bus speeds up to 12 Mbaud.
  • Each UART has transmit and receive LEDs.
  • High-Speed USB 2.0 port that can drive JTAG bus up to 30 Mbit/s (frequency settable by user).
  • Open drain buffers allow PS_SRST_B and PS_POR_B pins to perform software-based resets of Xilinx's Zynq platform.
  • Quad channel USB controller provides simultaneous access to both JTAG and UART interfaces.
  • Onboard buffers allow JTAG signals to operate at voltages from 1.8 V to 3.3 V.
  • Small form-factor surface-mount module can be directly loaded on target boards.
  • USB D+ and D-signals routed to pads, allowing USB connector to be placed anywhere on the host PCB.
  • VBUS_DETECT pin allows for reduced current consumption when the module isn't connected to a PC.
  • Product Compliance: HTC: 8473301180, ECCN: EAR99.
  • Included: JTAG-SMT4 programming module.
JTAG-HS2410-249
  • Analog Devices ADP123AUJZ Linear Regulator.
  • Programming cable; small, complete, all-in-one JTAG programming solution for Xilinx FPGAs.
  • Compatible with all Xilinx tools.
  • Compatible with IEEE 1149.7-2009 Class T0 - Class T4 (includes 2-Wire JTAG).
  • Separate VREF drives JTAG/SPI signal voltages; VREF can be any voltage between 1.8 V and  5V..
  • High-Speed USB2 port that can drive JTAG/SPI bus at up to 30 Mbit/s.
  • JTAG/SPI frequency settable by user.
  • Uses micro-AB USB2 connector.
  • SPI programming solution (modes 0 and 2 up to 30 Mbit/s, modes 1 and 3 up to 2 Mbit/s).
  • Fully supported by Digilent's Adept software and Adept SDK, allowing custom JTAG/SPI applications to be created.
  • Product compliance: HTC: 8471801000, ECCN: 3A992.a.
  • Included: One JTAG-HS2 programming cable.
JTAG-HS3410-299
  • Programming cable; small, complete, all-in-one JTAG programming/debugging solution for Xilinx FPGAs and SoCs.
  • Plugs directly into standard Xilinx JTAG 2.0 mm pitch header.
  • Separate VREF drives JTAG signal voltages; VREF can be any voltage between 1.8 V and 5 V.
  • High-Speed USB2 port that can drive JTAG bus up to 30 Mbit/s (frequency adjustable by user).
  • Compatible with Xilinx ISE 14.1 and newer, Xilinx Vivado 2013.3 and newer.
  • Uses USB Micro-B connector.
  • Open drain buffer on pin 14 allows debugging software to reset the processor core of Xilinx's Zynq platform.
  • Product compliance: HTC: 8473301180, ECCN: EAR99.
  • Included: One JTAG-HS3 programming cable.


Information on product safety:

Manufacturer:
Digilent (now a part of Emerson), 1300 NE Henley Ct. Suite 3, Pullman, WA 99163/USA
www.digilent.com

Responsible person:
Meilhaus Electronic GmbH, Am Sonnenlicht 2, 82239 Alling/DEU
info@meilhaus.com

Last seen